Clear Polycarbonate Dana 35 Differential Cover
Clear Polycarbonate Dana 35 Differential Cover

Clear Polycarbonate Dana 35 Differential Cover

$189.00
$189.00
Sold Out

A crystal-clear view into your rear differential, built for strength and clarity. Formed from rugged .187" thick polycarbonate, this cover delivers unmatched visibility and durability. Perfect for inspection, trail rigs, show builds, or just proving a point.

Made in the USA . Thermoformed in-house by Legacy Form USA.

Fits Dana 35 Rear Axles

Compatible with most Dana 35 rear differentials commonly found in Jeep vehicles from the late 1980’s through the mid-2000’s.

Common factory applications include:

Jeep:

  • Wrangler YJ (’87–’95)

  • Wrangler TJ (’97–’06)

  • Cherokee XJ (’84–’01)

  • Grand Cherokee ZJ (’93–’98)

  • Liberty KJ (’02–’07, select models)

If your Jeep is equipped with a Dana 35 rear axle, this Ghost Cover fits.

What’s In The Box?

  • One .187" thick, oleophobic ceramic coated polycarbonate differential cover

  • G1/4 bulkhead fitting and plug installed

  • Clear RTV silicone

  • 12" × 12" microfiber towel

  • Installation and care instructions

Care Guide

DO:

  • Use soft microfiber cloth (included)

  • Clean with water + mild dish soap

  • Blow off dust with clean compressed air before wiping (if available)

DO NOT:

  • Use harsh solvents (e.g. acetone, brake cleaner, or alcohol — polycarbonate doesn’t mind, but the ceramic coating will)

  • Use glass cleaners with ammonia

  • Pressure wash up close or hit with hot degreaser

  • Scrub with paper towels or abrasives

The UV- and oil-resistant coating is tough but not indestructible.

Warranty

12-Month Warranty
Covers manufacturing defects for one full year from purchase date.

Heat & Use Disclaimer

Heat control is important. Our clear differential covers are designed to withstand upwards of 300°, but exhaust pipes should be kept a minimum of 6" away or properly heat-shielded to prevent radiant heat damage.

Not recommended for heavy towing.

Legacy Form USA is not responsible for damage from external radiant heat sources.

Typically ships within 7–10 days.

Ghost Cover FAQ

A: We currently offer Ghost Covers for Duramax, LS, and SBC engine platforms. As well as AAM 11.5/11.8 differentials. Cummins and other applications are in development.

A: Yes — they’re thermoformed from optical-grade, heat-resistant polycarbonate. Each one is coated with a ceramic barrier for added oil repellency and durability.

A: No noticeable yellowing has occurred in testing. Covers are made from UV-stabilized polycarbonate and ceramic-coated for additional protection. Long-term exposure testing is ongoing, but results so far are excellent.

A: They’re made to run. Durability has been tested under heat, vibration, oil exposure, and real-world driving conditions. They’re not indestructible, but they’re absolutely built for real engines, not just display.

A: Installation is straightforward — apply the provided clear RTV sealant, allow it to partially cure (per instructions), then lightly snug the included hardware. We provide 29 bolts for a 28-bolt install… just in case the engine bay eats one.

A: Each cover is handcrafted, and minor imperfections may occur — particularly in areas like the flange or edge. These do not affect performance or clarity when installed. We inspect every cover and only ship what we believe you’ll be proud to run. Expect show-stopping engine bay visibility, not lab-grade perfection under LED magnifiers.

A: Crazing is a fine, hairline cracking that can appear in the polycarbonate during or shortly after ceramic coating. It typically shows up in high-stress flange areas caused by the thermoforming process.
It doesn’t affect strength or clarity in the visible zone and is mostly cosmetic. We actively work to minimize it, but it’s considered a normal characteristic of coated thermoformed polycarbonate.

A: We don’t currently offer a DIY ceramic kit, and flame polishing is not recommended post-forming. All covers ship pre-coated and flame-finished at the factory. Reach out if you’re chasing something custom — we’re happy to talk shop.

A: No — stick to mild soap and water only. Solvent-based cleaners like isopropyl alcohol, Windex, or ammonia can degrade the ceramic coating over time or cause hazing. Use a soft microfiber towel and wipe gently.